Radio Shack Cordless Telephone 43 3905 User Guide

43-3905  
User’s Guide  
Caller ID Wall Phone  
Thank you for purchasing your Caller ID Wall Phone from  
RadioShack. Please read this users guide before installing,  
setting up, and using your new phone.  
 
2/3  
b
Battery Notes:  
During battery replacement, keep the line cord plugged in and  
replace the batteries within two minutes to maintain Caller ID  
memory.  
When the low battery icon appears or the display dims, replace the  
batteries.  
Make sure the batteries fit tightly in the battery compartment.  
Dispose of old batteries promptly and properly.  
Do not burn or bury batteries.  
Use only fresh batteries of the required size and recommended  
type.  
Do not mix old and new batteries, different types of batteries  
(standard, alkaline, or rechargeable), or rechargeable batteries of  
different capacities.  
If you do not plan to use the phone for two weeks or longer,  
remove the batteries. Batteries can leak chemicals that can destroy  
electronic parts.  
2 Install Your Phone  
You can mount your phone on a wall plate, a wall, or place it on  
a desk or table.  
To mount the phone to a wall plate:  
1. Plug one end of the  
supplied short modular cord  
into the LINE jack at the  
back of the base.  
2. Plug the other end of the  
cord into the wall plate jack.  
3. Align the bases keyhole  
slots with the wall plate  
studs and slide the phone  
downward to secure it.  
 
3
To mount the phone directly on a wall:  
1. Drill two holes 3.25 inches (83 mm) apart, one below the  
other.  
2. Thread a screw into  
each hole, letting the  
heads extend about  
0.2”(5mm)  
0.2 inch (5mm) from  
the wall.  
3. Plug one end of  
the supplied long  
modular cord into the  
LINE jack at the back  
of the base.  
3.25”  
(83mm)  
4. Align the bases  
keyhole slots with the  
installed screws and slide the phone downward to secure it.  
To connect the handset, plug one end of the supplied coiled  
cord into the handsets modular jack. Then connect it to the jack  
on the left bottom of the base.  
n
Notes:  
Your local RadioShack store sells a variety of longer coiled handset  
cords, which are especially useful when you mount the phone on a  
wall.  
If your home has specially wired alarm equipment connected to  
the telephone line, ensure the installation of this system does not  
disable your alarm equipment. If you have questions about what  
will disable alarm equipment, consult your telephone company or  
a qualified installer.  
Select a location for your telephone that is near a telephone jack  
and not in the way of normal activities in the area.  
Your telephone connects directly to a modular telephone line  
jack. If your telephone wiring does not have a modular jack, you  
can update the wiring yourself using jacks and adapters (available  
 
4
3-line Display  
Shows name,  
number, date and  
time of incoming  
calls.  
NEW  
Flashes when you have  
new calls.  
DELETE  
Erases Caller ID  
information.  
CALL BACK  
Calls back the number  
shown on Caller ID.  
UP/DOWN  
Scroll through Caller ID  
records.  
M/S (Master/Secondary)  
Set to M.  
TONE/PULSE  
Set the dial mode for  
your phone system.  
VOLUME NORM/HI  
Set the call volume level.  
RINGER OFF/LO/HIGH  
Set the ringer volume or  
turn the ringer off.  
 
5
at your local RadioShack store), or have the telephone company  
update the wiring for you. You must use compatible modular jacks  
that are compliant with Part 68 of FCC Rules and the requirements  
adopted by the ACTA. The telephone cord and modular plug  
provided is Part 68 compliant for connecting to the telephone  
company network.  
3 Set Phone Options  
Phone Settings  
1. Hold down both UP and DOWN for about four seconds  
until ENTER LANGUAGE, then ENG ESP FRA appear, with  
ENG flashing.  
2. Press UP or DOWN to select the desired language, then  
press DELETE to confirm. LCD CONTRAST and 1 2 3 4 5  
appear on the display, with 3 flashing.  
3. Press UP or DOWN to select the contrast level (1-5), and  
press DELETE to confirm. ENTER AREA CODE appears, then  
_ _ _ appears, with the first _ flashing.  
4. Press UP or DOWN to select the first number of the area  
code, and press DELETE to confirm the selection. The  
flashing _ goes to the next digit.  
5. Repeat step 4 to set the second and third digits.  
Ringer  
If you do not want to hear the phone ring, slide RINGER to  
OFF. You can still make calls with the ringer off, and you can still  
answer calls if you hear another phone on the same line ring. If  
you want to hear the phone ring, set RINGER to HI or LO.  
 
6
Dial Mode  
Slide TONE/PULSE to the setting for the type of dialing service  
you have. If you are not sure which type you have, do this  
simple test.  
1. Slide TONE/PULSE to TONE. Lift the handset and listen for  
a dial tone.  
2. Press any number except 0. (If your setup requires that you  
dial an access code, usually 9, before you dial an outside  
number, do not press the access code number.)  
• If the dial tone stops, you have touchtone service. Keep  
the switch on TONE.  
• If the dial tone continues, you have pulse service. Set  
the switch to PULSE.  
Using Special Tone Services  
Some computer services require tone signals for communications.  
If you have pulse service, you can still simulate tone signals by  
following these steps.  
1. Connect to the special service using pulse dialing.  
2. When the special service answers, press to temporarily  
*
switch to tone dialing.  
3. When you complete the call, hang up to change the setting  
back to PULSE.  
Master/Secondary Setting  
For modern phones systems, slide M/S to M.  
n
Notes:  
If you have other phones with a Master/Secondary switch, set them  
to S. Set one system to answer and set the others to off.  
If M is not set on at least one phone, incoming calls might be  
disconnected.  
 
7
Do not connect more than four Caller ID modules (including this  
phone) that do not have Call Waiting to the same phone line.  
If you connect another type of Caller ID module that has Call  
Waiting to the same phone line as your system, the Call Waiting  
signal might be garbled or not received.  
Operation  
Making a Call  
1. Pick up the handset and wait for a dial tone.  
2. Use the keypad to enter the number you wish to dial. The  
number appears on the display.  
3. When you complete your call, hang up the handset. A few  
seconds later, the number disappears, and the display  
returns to normal.  
n
Note: If you dial a number over 15 digits, only the last 14  
digits appear on the display.  
Receiving a Call  
When you receive a call, the phone rings and the NEW indicator  
flashes. CALL# and the callers number appear on the display. To  
answer the call, pick up the handset.  
Timer  
This phone is designed with a clock timer to count the off-  
hook time in seconds, up to one hour. The timer appears on  
the display and starts to count up when you dial a number or  
answer an incoming call.  
n
Note: If you lift the handset and don’t dial a number, the timer  
appears and starts to count up after 10 seconds.  
 
8
Using Flash  
If you have Call Waiting, press FLASH to answer an incoming  
call without disconnecting the current call. Press FLASH again  
to return to the first call.  
n
Note: If you do not have Call Waiting, pressing FLASH might  
disconnect the current call.  
Using Redial  
To redial the last number you called, pick up the handset and  
press REDIAL when you hear a dial tone. The number scrolls  
across the display, and the phone automatically dials it.  
n
Note: The redial memory holds up to 32 digits, so you can redial  
long distance as well as local phone numbers.  
Using Pause  
Some telephone systems require you to dial an access code  
(usually 9) and wait for a second dial tone before dialing an  
outside number. When you manually dial a number, you can  
have your telephone pause anywhere during the dialing  
sequence. Simply press PAUSE at the desired location.  
When you redial a number, the telephone pauses for about four  
seconds at the pause entry. For longer pauses, press PAUSE  
again.  
Caller ID Operation  
If you subscribe to a Caller ID service, the phone automatically  
displays information about calls you receive and stores the  
information in Caller ID memory. The system can store up to 99  
incoming phone numbers or 64 incoming phone numbers with  
names into call records.  
 
9
During an incoming call, the phone company automatically  
sends the correct time between the first and second rings to  
update your systems display.  
Review Call Records  
Press UP or DOWN to review the new calls. After all new calls  
have been reviewed, END OF NEW CALL appears.  
To review all the records from oldest to newest, press UP. To  
review the records from newest to oldest, press DOWN. After  
reviewing all records in memory, END OF LIST appears.  
• If an incorrect, invalid, or incomplete Caller ID signal is  
received, LINE ERROR appears on the display.  
• If the name and number are not available due to the  
callers restriction, PRIVATE CALL appears on the display.  
• If the name and number are not available,  
--UNAVAILABLE-- appears on the display.  
RPT appears with a number if you have received a call  
from the same phone number more than once.  
• If you do not press a button within about 15 seconds, the  
system automatically returns to the normal display.  
n
Notes:  
The NEW indicator remains flashing until you have reviewed all  
new calls.  
The number of new calls does not change until all calls have been  
reviewed and END OF NEW CALL appears. The new call counter  
then resets to 0.  
Call Back from Caller ID Memory  
1. Press UP or DOWN to find the number to call back.  
2. Press CALL BACK twice. LIFT HANDSET or PICK UP CALL  
appears.  
 
10  
3. Lift the handset, and the number is redialed automatically.  
Follow these steps to select one of the options for Caller ID  
call back.  
1. Press UP or DOWN to find the Caller ID memory location  
to be redialed.  
2. Press CALL BACK. The 7- or 11-digit number flashes.  
3. Press UP or DOWN to select one of the four options.  
Option 1  
Option 2  
Option 3  
Option 4  
1 + Area Code + 7-digit number (11 digits)  
1+7-digit number (8 digits)  
Area Code + 7-digit number (10 digits)  
7-digit number  
4. Press CALL BACK again to confirm.  
5. Pick up the handset, and the selected number is dialed  
automatically.  
Delete Call Records  
You can select and delete an individual call record, or all call  
records stored in the system.  
To delete a single call record, press UP or DOWN until the  
call record you want to delete appears. Press DELETE twice.  
The call record is deleted, and the system automatically  
renumbers the remaining call records.  
To delete all call records after all new calls have been  
reviewed, hold down DELETE for about three seconds.  
ERASE ALL CALLS appears. Press DELETE. The system  
deletes all call records. NO CALLS appears, and then TOTAL:  
00 NEW: 00 appears.  
n
Notes:  
When the phones memory is full, it automatically replaces the  
oldest call record with the newest incoming call.  
 
11  
If you do not press any button within about 15 seconds while  
ERASE ALL CALLS appears on the display, the phone automatically  
returns to normal display and the records are not deleted.  
Additional Information  
Important Safety Information  
When using your telephone equipment, basic safety  
precautions should always be followed to reduce the risk of fire,  
electric shock and injury to persons, including the following:  
• Do not use this product near water, for example, near a  
bath tub, wash bowl, kitchen sink or laundry tub, in a wet  
basement or near a swimming pool.  
• Avoid using a telephone (other than a cordless type) during  
an electrical storm. There may be a remote risk of electric  
shock from lightning.  
• Do not use the telephone to report a gas leak in the vicinity  
of the leak.  
• Handle the phone carefully. Do not drop it.  
• Do not use or store the phone in extreme temperatures.  
Service and Repair  
If your telephone is not performing as it should, take it to your  
local RadioShack store for assistance. To locate your nearest  
RadioShack, use the store locator feature on Radioshack’s  
7422) and follow the menu options. Modifying or tampering  
with the telephones internal components can cause a  
malfunction and might invalidate its warranty and void your  
FCC authorization to operate it.  
 
12  
Surge Protection  
Your telephone has built-in protection circuits to reduce the  
risk of damage from surges in telephone line and power line  
current. These protection circuits meet or exceed the FCC  
requirements. However, lightning striking the telephone or  
power lines can damage your telephone. Lightning damage is  
not common. Nevertheless, if you live in an area that has severe  
electrical storms, we suggest that you unplug your phone when  
storms approach to reduce the possibility of damage.  
FCC Information  
FCC Part 15  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant  
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful  
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency  
energy and, if not installed and used in accordance with the instructions, may cause harmful interference  
to radio communications. However, there is no guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to radio or television reception, which can be  
determined by turning the equipment off and on, the user is encouraged to try to correct the interference  
by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult your local RadioShack store or an experienced radio/TV technician for help.  
If you cannot eliminate the interference, the FCC requires that you stop using your equipment. Changes or  
modifications not expressly approved by RadioShack may cause interference and void the users authority  
to operate the equipment.  
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1)  
This device may not cause harmful interference, and (2) This device must accept any interference received,  
including interference that may cause undesired operation.  
FCC Part 68 and ACTA  
a) This phone complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the  
bottom of this equipment is a label that contains, among other information, a product identifier in the  
format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.  
b) The registration jack USOC for the equipment is RJ11C or RJ11W.  
c) This equipment is designed to be connected to the telephone network or premises wiring using a  
compatible modular jack which is Part 68 compliant. A compliant telephone cord and modular plug is  
provided with this product. See installation instructions for details.  
d) The REN is useful to determine the quantity of devices that may be connected to the telephone line.  
Excessive RENs on the telephone line may result in the devices not ringing in response to a n incoming  
call. In most, but not all areas, the sum of RENs of all devices should not exceed five (5). To be certain of  
the number of devices that may be connected to a line, as determined by the total RENs, contact the local  
telephone company.  
e) If this phone causes harm to the telephone network, the telephone company will notify you in advance  
that temporary discontinuance of service may be required. But if advance notice isn’t practical, the  
telephone company will notify the customer will be notified as soon as possible. You will be advised of your  
right to file a complaint with the FCC if you believe it is necessary.  
f) Your telephone company may make changes in its facilities, equipment, operations, or procedures that  
could affect the operation of your equipment. If they do, you will be given advance notice so as to give you  
an opportunity to maintain uninterrupted service.  
 
13  
g) If you experience trouble with this phone, please contact your service provider for repair/warranty  
information. If your equipment is causing harm to the telephone network, the telephone company may  
request that you disconnect the equipment until the problem is resolved.  
h) No repair can be done to this equipment.  
i) Connection to party line service is subject to state tariffs. Contact the state public utility commission,  
public service commission or corporation commission for information.  
j) If your home has specially wired alarm equipment connected to the telephone line, ensure the installation  
of this phone does not disable your alarm equipment. If you have questions about what will disable alarm  
equipment, consult your telephone company or a qualified installer.  
k) This phone is hearing aid compatible.  
Limited Warranty  
RadioShack warrants this product against defects in materials and workmanship under normal use by  
the original purchaser for one (1) year after the date of purchase from a RadioShack-owned store or an  
authorized RadioShack franchisee or dealer. RADIOSHACK MAKES NO OTHER EXPRESS WARRANTIES.  
This warranty does not cover: (a) damage or failure caused by or attributable to abuse, misuse, failure to  
follow instructions, improper installation or maintenance, alteration, accident, Acts of God (such as floods  
or lightning), or excess voltage or current; (b) improper or incorrectly performed repairs by persons who are  
not a RadioShack Authorized Service Facility; (c) consumables such as fuses or batteries; (d) ordinary wear  
and tear or cosmetic damage; (e) transportation, shipping or insurance costs; (f) costs of product removal,  
installation, set-up service, adjustment or reinstallation; and (g) claims by persons other than the original  
purchaser.  
Should a problem occur that is covered by this warranty, take the product and the RadioShack sales  
receipt as proof of purchase date to any RadioShack store in the U.S. RadioShack will, at its option, unless  
otherwise provided by law: (a) repair the product without charge for parts and labor; (b) replace the product  
with the same or a comparable product; or (c) refund the purchase price. All replaced parts and products,  
and products on which a refund is made, become the property of RadioShack. New or reconditioned  
parts and products may be used in the performance of warranty service. Repaired or replaced parts and  
products are warranted for the remainder of the original warranty period. You will be charged for repair or  
replacement of the product made after the expiration of the warranty period.  
RADIOSHACK EXPRESSLY DISCLAIMS ALL WARRANTIES AND CONDITIONS NOT STATED IN THIS  
LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW, INCLUDING  
THE IMPLIED WARRANTY OF MERCHANTABILITY AND, IF APPLICABLE, THE IMPLIED WARRANTY  
OF FITNESS FOR A PARTICULAR PURPOSE, SHALL EXPIRE ON THE EXPIRATION OF THE STATED  
WARRANTY PERIOD.  
EXCEPT AS DESCRIBED ABOVE, RADIOSHACK SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO  
THE PURCHASER OF THE PRODUCT OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY  
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE  
PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED  
TO, ANY DAMAGES RESULTING FROM INCONVENIENCE AND ANY LOSS OF TIME, DATA, PROPERTY,  
REVENUE, OR PROFIT AND ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,  
EVEN IF RADIOSHACK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.  
Some States do not allow limitations on how long an implied warranty lasts or the exclusion or limitation  
of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This  
warranty gives you specific legal rights, and you may also have other rights which vary from State to State.  
You may contact RadioShack at:  
RadioShack Customer Relations, 300 RadioShack Circle, Fort Worth, TX 76102  
04/08  
Protect the environment by recyling used electronics. Go to E-CyclingCentral.com to find  
an electronic recycling center near you.  
©2009. RadioShack Corporation.  
All rights reserved. RadioShack and RadioShack.com are  
trademarks used by RadioShack Corporation.  
Printed  
in China  
11A09  
43-3905  
4LM053Y2  
 
14  

Pyramid Car Audio Car Amplifier PA 305 User Guide
QSC Audio Car Amplifier ISA 450 User Guide
Radio Shack Marine Radio PRO 2046 User Guide
RCA Dishwasher 165D3527P035 User Guide
RCA DVD VCR Combo DVD VCR User Guide
RocketFish Digital Camera RF NBWEB User Guide
Salton Coffee Grinder FAC500G User Guide
Samsung Projection Television HL R5678W User Guide
Sanus Systems TV Mount VLT15 User Guide
Scag Power Equipment Edger SE 3BS User Guide