PYLE Audio TV Mount PSW117ET1 User Guide

Step 3: Hanging display  
Firstly lift the bracket mounted display over the wall mount. And then hook the  
brackets over the top of the wall mount. Rotate the display let the bottom of the  
brackets hook over the bottom of wall mount, as shown in Fig.3a. Then put safe  
bolts into the bottom of the brackets and lock it, as shown in Fig.3b.  
Warning: Some TV require two people to lift, as we are not responsible for any  
personal injury or product damage due to mishandling.  
Tilt Flat Panel TV Bracket  
Multifunctional double deck wall mount  
INSTALLATION GUIDE  
2,3  
Item No.:PSW117ET1  
UP  
UP  
6
1
Fig 3a  
Fig 3b  
UP  
UP  
Thank you for choosing our products  
Easy installing: Just hang up the display  
Safety: locking by spinning bolt on the bottom  
Max load capacity:60kg/132lbs  
TV size range: 36"~65"  
Pyle Audio  
Adjustable angle: -5 15  
1600 63rd st , Brooklyn, NY, 11204  
(718)236-8000  
Inside has balance adjust system  
www.pyleaudio.com  
Bulit in leveler system  
MADE IN CHINA  
-8-  
IMPORTANT: If don’t understand about right install ways, please  
consult to normal installing specialist.  
 
Step 2: Attach mount to wall  
We are not responsible for any personal injury or product damage  
due to mishandling, incorrect mounting, incorrect assembly or  
incorrect use of this product.  
WARNING  
First, determine the height of stand  
The best height of stand is parallel to eyelevel of a person who sitting on a couch.  
Normally, the horizontal distance of eyelevel is about 4’ from ground level.  
The following two conditions are for determining the perfect height of stand:  
1) the distance between wall and couch(Fig 2a).  
Note: The supplied wall mounting hardware is not for use on steel stud walls or cold  
cinder block walls. If you are uncertain about the nature of your wall, please consult a  
qualified contractor. If the hardware you required is not included please contact your  
local hardware store.  
2) the distance of eyelevel from ground level plus the distance measured from  
eyelevel of a person sitting on couch with viewing angle of 15°(Fig 2a).  
Caution:  
This Product LCD /Plasma Wall Mount Bracket is intended for use only  
with the maximum weights indicated .See apparatus instructions .Use with products  
heavier than the maximum weights indicated may result in instability causing possible  
injury .  
For example:  
1) the distance of ‘a’ is 5’-7’, the distance of ‘b’ is about 1’  
2) the distance of ‘a’ is 8’-13’, the distance of ‘b’ is about 3’  
3) the distance of ‘a’ is 14’-17’, the distance of ‘b’ is about 4’  
The perfect height of stand centre will be anywhere within b, where you feel  
comfortable for viewing.  
Step 1: Attach bracket to TV  
If your display hole’s vertical distance> 400mm, you need to use the lengthen  
bracket on both brackets(2,3).Lengthen bracket(4,5) installation:  
According your display hole's distance to choose the bracket hole's.  
Install the Lengthen bracket(4,5) directly to the both brackets(2,3) by using  
M6x50mm(9) bolts M6 washers(8) and M6 nuts(7), As shown in Fig 1a.  
15 degree  
viewing angle  
b
UP  
UP  
4
3
8
5
7
9
UP  
eyelevel  
UP  
a
2
UP  
UP  
Fig 1b  
Fig 2a  
Fig 1a  
Check your TV manual to confirm the diameter of bolt to be used or choose an  
appropriate bolt according to size, height and position of the holes on your TV. See  
pages 4-5 of these instructions for examples.  
For correct installing, make sure that hook of every bracket must facing down. Use  
selected bolts, spacers and washers for installing bracket at the back of display.  
Adjust two brackets to equal heights and level. Once aligned, tightly secure the  
bolts. Note: the " UP"side on the top. As shown in Fig.1b.  
-3-  
-6-  
 
Following examples shows how to use bolts, spacers and square washers.  
2. Some displays have curved backs with  
recessed mounting lands(Fig.a). It will  
require the use of spacer. For this display,  
install a spacer(M)between display and  
the bracket. As shown in Fig 1d.  
1.Some displays have vertical backs. No spacer is required. Install the bracket directly  
to the back of display by using bolts and square washers provided. As shown in Fig.1c.  
Fig a  
M4 Fig bit  
M5 Fig bit  
M5 Fig bit  
M
M6 Fig bit  
I
I
I
A,B  
I
F
3
2
C
M
2
3
G
2
3
M
3
I
I
E
D
I
H
M6 Fig bit  
M8 Fig bit  
M8 Fig bit  
Fig 1d  
Fig 1c  
-5-  
-4-  
 

QSC Audio Portable Speaker MD LP118 User Guide
Renesas Computer Hardware SH7670 User Guide
Renesas Network Card M38000TL2 FPD User Guide
Ricoh Digital Camera L753 2911 User Guide
RocketFish Network Card RF WHD100 User Guide
Ryobi Saw SS50 User Guide
Ryobi Trimmer RY30542 User Guide
Samsung Personal Computer DP500A2DK01UB User Guide
Samsung Refrigerator DA68 01454B User Guide
Sanyo Air Conditioner 36U72R User Guide